· · 6 min read

Wood Shredder Specifications: kW, T/h, Output

Wood shredder specifications come down to 4 numbers: 55 to 500 kW of power, 2 to 60 tons per hour of throughput, a feed opening of 6 to 60 inches, and an output size of 10 to 100 mm set by screens. Throughput is measured in tons per hour at a stated moisture content and screen size, so two machines can only be compared at the same output specification. This guide decodes every line of a wood shredder specifications sheet so you can match power, capacity, and particle size before you buy.

Key Takeaways

  • Power from 55 to 500 kW (74 to 670 HP) sets the ceiling; throughput of 2 to 60 T/h depends on screens and material.
  • Throughput is quoted at 1 moisture level and 1 screen size — changing from 20 mm to 50 mm can double T/h.
  • Feed openings run 6 in / 150 mm on compact units to 60 in / 1500 mm on industrial twin-shaft models.
  • Output size is controlled by screens from 10 to 100 mm; fines below 5 percent require sharp cutters and correct speed.
  • Ask WeiDong Machinery for a guaranteed T/h figure tied to your material photos and screen choice.

What Do Wood Shredder Power Ratings Mean?

Three power formats appear on spec sheets, and they are not interchangeable:

  • Diesel engines — 100 to 500 kW (134 to 670 HP), best for remote yards; fuel use runs 12 to 25 liters per hour at full load.
  • Electric motors — 55 to 400 kW, roughly 30 percent cheaper energy per ton where grid or a 200-plus kVA genset exists.
  • PTO drive — 60 to 150 HP tractors for farm units at 2 to 8 T/h; cheapest where a tractor already exists.

Torque matters more than headline kW for shredders. Twin-shaft slow-speed machines deliver 20000 to 80000 Nm at 20 to 60 rpm to tear contaminated timber, while high-speed single-shaft units spin at 400 to 800 rpm with lower torque for uniform chips. A 200 kW slow-speed shredder can out-produce a 300 kW high-speed unit in demolition wood because it stalls 50 percent less often. Browse the power options in our wood shredder lineup.

Power bandDriveTypical T/hBest for
55 to 110 kWElectric or PTO2 to 8Farms, joinery, pallet repair shops
110 to 220 kWDiesel or electric8 to 20Pallet recycling, mulch yards
220 to 350 kWDiesel15 to 35Biomass fuel, land clearing
350 to 500 kWDiesel30 to 60Industrial biomass, storm debris

How Is Throughput Measured in T/h?

Throughput in tons per hour is the headline figure buyers compare, yet 4 variables sit behind every number:

  1. Moisture content — green wood at 45 percent moisture weighs nearly twice as much per cubic yard as dry wood at 15 percent.
  2. Bulk density — hardwood chips at 350 kg per cubic meter move fewer cubic yards per ton than straw at 120 kg.
  3. Screen size — a 50 mm screen passes 2 to 3 times more tons per hour than a 20 mm screen on the same machine.
  4. Feed method — grapple-fed continuous operation beats manual feeding by 30 to 50 percent in real yards.

Reputable suppliers quote T/h with all 4 stated, for example 12 T/h at 40 percent moisture through a 30 mm screen grapple-fed. If a quote omits the screen size, assume the largest screen was used. Ask our sales team for throughput curves at 2 screen sizes before shortlisting.

What Feed Opening and Output Size Do You Need?

Size the feed opening 2 inches above your largest typical piece to stop bridging:

  • Compact 6 to 12 in / 150 to 300 mm — branches, offcuts, pallets at 2 to 10 T/h.
  • Mid-range 16 to 32 in / 400 to 800 mm — logs, crates, furniture waste at 10 to 25 T/h.
  • Industrial 40 to 60 in / 1000 to 1500 mm — whole trees, demolition timber, stumps at 25 to 60 T/h.

Output size follows the buyer, not the machine. Mulch tolerates 30 to 50 mm with 10 to 15 percent fines, animal bedding needs 15 to 30 mm dry material, pellet plants demand uniform 20 to 30 mm with fines below 5 percent, and boiler fuel accepts 30 to 80 mm. Screens from 10 to 100 mm set the top size; rotor speed and cutter sharpness set uniformity. A 2-person screen change takes 20 to 40 minutes, so one machine can serve 2 markets same-day. See screen options under accessories and parts.

How Do You Read a Spec Sheet in 5 Minutes?

Run this 7-line check on every finalist to compare equal to equal:

  • Confirm power in kW and HP plus rpm — slow-speed high-torque versus high-speed matters for dirty wood.
  • Read T/h together with screen size and moisture — normalize to your screen before comparing prices.
  • Check feed opening in inches and mm against your largest piece plus 2 inches of clearance.
  • Note cutter count (20 to 40 stations) and replacement cost per set ($1500 to $6000).
  • Verify weight (8 to 45 tons) and transport size for permits and crane plans.
  • Confirm warranty of 12 months or 2000 hours plus English manuals and wiring diagrams.
  • Compare delivery of 15 to 30 days standard versus 60 to 90 days for custom builds.

Factory-direct machines from WeiDong Machinery typically land 20 to 40 percent below dealer equivalents while including export packing and a spare cutter set worth $800 to $1500. For high-volume contaminated streams also price a horizontal grinder on the same per-ton basis.

Frequently Asked Questions

What do wood shredder specifications mean?

Power in kW sets the cutting ceiling, T/h states throughput at one screen size and moisture level, feed opening in inches or mm sets the largest piece accepted, and output size in mm is controlled by screens from 10 to 100 mm.

How is wood shredder throughput measured?

In tons per hour weighed across 6 to 8 hour shifts at a stated moisture content and screen size. Reputable tests report 3 to 5 runs averaged, grapple-fed, with fines percentage included.

What size wood shredder do I need for 10 tons per hour?

A 150 to 220 kW single-shaft unit with a 16 to 24 in feed opening covers 10 to 15 T/h in clean wood through a 30 mm screen. Add 30 percent power margin for demolition timber with nails.

Should I choose diesel or electric?

Choose diesel from 100 to 500 kW for mobile or remote work, and electric from 55 to 400 kW where grid exists — energy per ton costs roughly 30 percent less. Farms with a 90 to 150 HP tractor should also price PTO drive.

Next Step

Send WeiDong Machinery your material photos, target output size, and weekly tonnage for a guaranteed T/h match with an ex-works price. Start at the wood shredder lineup or message our sales team — replies arrive within one business day.

Keep reading