· · 8 min read
Used Tub Grinder: Inspection Checklist and Prices
A used tub grinder in good condition typically sells for 40 to 65 percent of its new price, with machines under 3,000 engine hours holding the top of that range and units over 6,000 hours dropping toward 20 to 30 percent. Buying used makes sense when the rotor, tub floor, bearings, and engine all check out — but a worn hammermill can hide $25,000 to $50,000 in rebuild costs that erase the discount. This guide gives you a 15-point used tub grinder inspection checklist, hour-meter benchmarks, and fair-price math so you can decide between used and new with confidence.
Key Takeaways
- A sound used tub grinder sells for 40 to 65 percent of new; units under 3,000 hours hold value best.
- Budget $25,000 to $50,000 for a full rotor, screen, and bearing rebuild on high-hour machines.
- Inspect 15 points: rotor, hammers, screens, tub floor, bearings, engine, hydraulics, clutch, belts, electrics, frame, running gear, drive, safety, and paperwork.
- Machines over 6,000 engine hours need oil analysis and compression data before you bid a dollar.
- Always compare against a factory-direct new quote from WeiDong Machinery — new sometimes beats used per ton.
What Is a Fair Price for a Used Tub Grinder?
Fair used pricing tracks engine hours, rebuild history, and remaining wear-part life more than calendar age. Use these benchmarks as a share of the equivalent new machine price:
| Condition | Engine hours | Share of new price | Example on a $380,000 new unit |
|---|---|---|---|
| Low-hour, dealer-serviced | Under 2,000 h | 60 – 75% | $228,000 – $285,000 |
| Mid-life, full records | 2,000 – 4,000 h | 45 – 60% | $171,000 – $228,000 |
| High-hour, needs wear parts | 4,000 – 6,000 h | 30 – 45% | $114,000 – $171,000 |
| Rebuild candidate | Over 6,000 h | 20 – 30% | $76,000 – $114,000 |
Four factors move a machine up or down within its band. First, engine emission tier: Tier 4 Final units from 2015 onward carry a 10 to 15 percent premium over older Tier 3 machines because parts and compliance are simpler. Second, running gear: tracked units cost 12 to 18 percent more than wheeled equivalents. Third, included tooling: a machine with 3 screen sizes and a spare hammer set is worth $8,000 to $15,000 more than a bare unit. Fourth, region: machines near Gulf Coast and Pacific Northwest woodyards trade 5 to 10 percent higher due to steady biomass demand. Browse current new-model specs on our tub grinder range to anchor your comparison before negotiating.
How Many Hours Are Too Many on a Used Tub Grinder?
There is no single cutoff — hours matter relative to rebuild history and price. Here is how experienced buyers read the meter:
- Under 2,000 hours: break-in complete, 80 percent or more of component life remaining. Pay top-band prices only with service records and at least 50 percent hammer life left.
- 2,000 to 4,000 hours: the sweet spot for value. Expect one hammer change ($2,000 – $5,000) and screen work within the first 500 hours of your ownership; diesel engines at this age still deliver rated 400 to 550 kW output.
- 4,000 to 6,000 hours: plan a $25,000 to $50,000 rebuild allowance covering hammers, screens, anvils, belts, and at least 2 bearings. Rotor bearings typically last 3,000 to 6,000 hours and tub floor liners 2,500 to 5,000 hours, so both are suspect here.
- Over 6,000 hours: engine overhaul territory — $30,000 to $60,000 for a 500 HP-class diesel with 8,000 to 12,000-hour overhaul intervals. Buy only below 30 percent of new price, and only with oil analysis, blow-by checks, and compression data.
A 1,800-hour machine with no records is riskier than a 4,200-hour unit with stamped service books, new hammers at 4,000 hours, and bearing replacement receipts. Hours tell you where to look; paperwork tells you what you will spend. Our tub grinder maintenance schedule shows exactly which intervals should be stamped at each milestone.
15-Point Used Tub Grinder Inspection Checklist
Take 2 to 3 hours on site with a flashlight, a grease gun, and a dial indicator if possible. Work through all 15 points:
- Rotor and hammers (20–40 hammers) — count missing, cracked, or backward hammers; measure remaining face. Less than 50 percent life means a $2,000 to $5,000 change within months.
- Screens (2–6 segments) — look for cracks, blinded openings, and re-welded frames; new sets run $4,000 to $9,000.
- Tub floor and liners — thin or holed liners signal 2,500-plus hours of abrasive feed; replacement costs $8,000 to $18,000 with labor.
- Rotor bearings (4–6 stations) — feel for play and heat after a 30-minute test run; a seized bearing repair reaches $5,000 to $12,000.
- Anvils and breaker bars — check gap and edge condition; replacement every 1,500 to 2,500 hours at $1,500 to $4,000.
- Engine — cold-start it yourself, watch exhaust color for 5 minutes, and pull oil and coolant samples; milky oil or 3-plus fault codes are walk-away signs.
- Clutch and driveline — engage under load and listen for slip; clutch jobs cost $6,000 to $14,000.
- Hydraulics — cycle the tub tilt and conveyor, check for creep, and inspect hoses; full hose replacement runs $3,000 to $7,000.
- Belts and sheaves — glazing, cracking, or wobble means $2,000 to $6,000 in parts.
- Electrics and controls — test every e-stop, tub-stop bar, and the remote; obsolete controllers can strand a machine for weeks.
- Frame and tub structure — dye-pen or visually check welds at the tub ring and axle mounts for cracks.
- Running gear — measure track-pad or tire wear; a set of tracks costs $15,000 to $30,000.
- Discharge conveyor (30–50 ft) — check belt splices, tracking, and skirt sealing under load.
- Safety and fire systems — confirm extinguisher charge dates and that fines have been cleaned from the engine bay; fines cause 1 in 5 engine-compartment fires.
- Paperwork — verify serial numbers, lien release, hour-meter consistency with service stamps, and remaining 12 to 18 month warranty transfer if any. Confirm the engine serial matches the dataplate — mismatched plates void Tier 4 compliance and cut resale 10 percent or more.
Photograph every dataplate and wear surface — honest sellers expect it, and the photos let our engineers estimate rebuild parts from accessories and parts before you bid.
New vs Used: Which Costs Less Per Ton?
Run 5-year math, not sticker math. Example: a used unit at $170,000 plus a $35,000 rebuild totals $205,000. Over 5 years at 1,200 hours and 15 tons per hour (90,000 tons), capital cost is $2.28 per ton. A new factory-direct machine at $380,000 over the same 90,000 tons costs $4.22 per ton in capital — but burns 8 to 12 percent less fuel, carries a full warranty, and avoids 2 to 3 weeks of rebuild downtime worth $15,000 to $30,000 in lost production.
The used deal wins only when three conditions hold: purchase plus rebuild stays under 65 percent of new, the engine tests clean, and downtime for repairs costs you less than $10,000. Otherwise new factory-direct from WeiDong Machinery — typically 20 to 40 percent below dealer imports — is the lower-risk buy. Read how to choose a wood grinder to size the right class first, then request both numbers through our contact page and compare honestly.
Frequently Asked Questions
Is buying a used tub grinder worth it?
Yes, when a mid-life machine (2,000–4,000 hours) with records prices at 45 to 60 percent of new and needs less than $35,000 in rebuild work. Above 6,000 hours or without paperwork, new factory-direct machines usually cost less per ton over 5 years.
What hours are too many on a used tub grinder?
Over 6,000 engine hours is rebuild-or-overhaul territory: budget $25,000 to $50,000 for rotor and wear parts plus $30,000 to $60,000 if the 500 HP-class engine needs overhaul. Buy at that age only below 30 percent of new price with oil analysis in hand.
How much does it cost to rebuild a tub grinder rotor?
A full rotor refresh — 20 to 40 hammers, screens, anvils, and 2 or more bearings — costs $25,000 to $50,000 in parts plus 3 to 5 days of labor. Genuine kits from accessories and parts ship within 7 days when you quote your serial number.
Where can I compare used prices against new factory prices?
Send the used machine's spec sheet and asking price to WeiDong Machinery via our contact page — we return a matching new factory-direct quote within 1 business day so you can compare total cost per ton side by side.
Get a Factory-Direct Price Before You Bid
A 10-minute quote request can save you $50,000 on a bad used deal. Tell us the used machine's hours, rotor size, and asking price, and we will benchmark it against a new tub grinder with matching 10 to 40 T/h capacity, 74 to 700 kW power options, and 7-day parts dispatch. If used still wins, our maintenance schedule will keep it earning from day one.