· · 6 min read
Straw Shredder Specifications: kW, T/h, Output Size
Straw shredder specifications boil down to 4 numbers: drive power in kW or HP, throughput in tons per hour, feed opening in millimeters, and output size in millimeters. A mid-range diesel straw shredder rated 150 to 260 kW typically processes 8 to 20 T/h through a 1,200 to 1,650 mm wide chamber into 10 to 40 mm screened output. This guide from WeiDong Machinery decodes each straw shredder specification line so you can compare any two spec sheets in 10 minutes.
Key Takeaways
- Power (55–450 kW) sets the ceiling: roughly 1 kW drives 60 to 100 kg/h of dry straw.
- Throughput (2–50 T/h) is quoted on dry wheat straw; corn stover runs 20 to 30 percent lower.
- Feed opening (1,000–1,865 mm wide) must clear your largest bale plus 100 mm per side.
- Output screens (10–40 mm) decide your market: feed, bedding, biomass or board furnish.
- Always compare power, throughput, opening and output together — single numbers mislead.
How Do Power Ratings Work?
Power is quoted in kW for electric models and HP or kW for diesel and PTO units (1 HP = 0.746 kW):
| Class | Rated power | Real throughput | Full-load fuel/draw |
|---|---|---|---|
| Compact PTO | 37–90 kW (50–120 HP tractor) | 2–6 T/h | Tractor diesel 8–18 L/h |
| Mid-range diesel | 110–260 kW (150–350 HP) | 8–20 T/h | 20–45 L/h |
| Industrial diesel | 300–450 kW (400–600+ HP) | 25–50+ T/h | 50–75 L/h |
| Electric stationary | 75–400 kW | 6–40 T/h | 75–400 kWh per hour |
Two traps to avoid. First, peak versus continuous ratings: some brochures quote a 30-minute peak 20 percent above the continuous rating the machine can actually hold — always size on continuous power. Second, derating: above 1,000 m altitude or 40°C ambient, naturally aspirated diesels lose 8 to 12 percent of rated output. WeiDong Machinery publishes continuous ratings at 25°C sea level so quotes compare like-for-like on our straw shredder page.
What Does Throughput (T/h) Really Mean?
Rated tons per hour assume dry wheat straw at 12 to 15 percent moisture, 120 to 150 kg/m³ bale density, and the largest screen aperture. Real yards see 3 discounts:
- Material discount — corn stover and damp bales run 20 to 30 percent below wheat-straw ratings; manure packs 25 to 35 percent below.
- Screen discount — a 10 mm feed screen produces 35 to 45 percent fewer tons per hour than a 40 mm screen on the same machine.
- Duty discount — ratings assume 50 minutes of feeding per hour; single-loader yards achieve 35 to 45 minutes, cutting effective output 15 to 25 percent.
Worked check: a shredder rated 15 T/h on wheat straw with a 40 mm screen delivers roughly 9 to 11 T/h on corn stover through a 20 mm screen in a single-loader yard. Size on your worst-case combination, then add 20 percent headroom — never on brochure maximums. Our sales engineers will re-rate any model for your bale mix free of charge.
How Do Feed Opening and Output Size Work?
The feed opening (width × height in mm) decides what goes in; the screen aperture (mm) decides what comes out:
- Feed width 1,000–1,200 mm — suits 1.2 m round bales and small squares; needs pre-breaking for 1.8 m big squares.
- Feed width 1,650–1,865 mm — swallows 1.8 m big squares whole with 100 mm clearance per side; the commercial sweet spot.
- 10–15 mm output — feed-mix and pellet furnish; lowest T/h but highest $25 to $45 per ton premium.
- 20–25 mm output — animal bedding and mushroom substrate; the volume market at 60 percent of sales.
- 30–40 mm output — biomass fuel and board furnish; highest T/h, lowest processing cost per ton.
Rotor speed (800 to 1,500 rpm) and hammer count (32 to 64) fine-tune the cut: higher tip speeds below 90 m/s give cleaner 10 to 15 mm cuts with 10 to 15 percent more energy per ton. Keep 2 to 3 screen sets on hand — a $400 to $900 set changeover takes 30 to 45 minutes and opens a second revenue stream. Order exact-fit screens from WeiDong parts.
How Do You Read Any Spec Sheet in 10 Minutes?
Run this 6-line checklist against every candidate, including wood chipper alternatives if your diet includes woody stalks:
- Continuous power — kW or HP at stated altitude and temperature, not peak.
- Rated throughput with conditions — material, moisture, screen size and duty cycle attached.
- Feed opening vs. your bales — largest bale dimension plus 200 mm total clearance.
- Screen range — 10 to 40 mm coverage for all 2 to 3 target markets.
- Rotor and hammer count — 32 to 64 swing hammers, tip speed, and reversibility.
- Weight and footprint — 3 to 12 tons and 6 to 12 m length determines transport and pad cost.
Red flags: missing moisture basis, single throughput number with no screen stated, no continuous power temperature reference, or weight 20 percent below peers (thin steel that cracks within 2 seasons). Machines passing all 6 lines can be compared purely on price per proven ton per hour.
Frequently Asked Questions
What do straw shredder specifications mean?
Power (kW/HP) sets maximum throughput, T/h states tons per hour on specified material and screen, feed opening (mm) states the largest bale accepted, and output size (mm) states the screened particle range your buyers receive.
How is straw shredder throughput measured?
On dry wheat straw at 12 to 15 percent moisture through the largest screen at 50 minutes feeding per hour. Expect 20 to 30 percent less on corn stover or damp bales, and 35 to 45 percent less through fine 10 mm screens.
How much power does a straw shredder need?
Roughly 1 kW of continuous power per 60 to 100 kg/h of dry straw: 37 to 90 kW for 2 to 6 T/h, 110 to 260 kW for 8 to 20 T/h, and 300 to 450 kW for 25 to 50+ T/h industrial duty.
What output size should I choose?
Choose 10 to 15 mm for feed and pellets, 20 to 25 mm for bedding and substrate, and 30 to 40 mm for biomass fuel. Most commercial yards stock 2 to 3 screen sets to serve multiple markets from one machine.
Next Step
Send WeiDong Machinery your bale dimensions and target output size for a re-rated throughput figure within one business day. Compare real specs on the straw shredder lineup or ask our sales team for a side-by-side sheet.