· · 3 min read
Tub Grinder for Pallets Setup Guide
A tub grinder for pallets setup guide helps pallet recyclers convert used pallets into boiler fuel, animal bedding and mulch. Pallets are dense, nail-ridden and mixed-species, so the setup has to protect the hammer mill first. Tub grinders handle pallets well when magnets, feed control and screens are configured correctly. WeiDong Machinery supplies tub grinders rated for pallet recycling, and this guide covers magnet placement, feed control, screens and the daily routine.
Key Takeaways
- Use a magnetic separator plus a cross-belt magnet for pallet feed.
- Run the tub at 40 to 60 percent speed for steady pallet grinding.
- Use a 2 to 3 inch screen for boiler fuel and 1 inch for bedding.
- A tub grinder processes 15 to 30 tons per hour on pallets.
- Check hammers daily; nails and mixed density wear tools fast.
Feed Preparation
Pallets need a two-stage metal defense. Run a magnetic separator before the tub to pull loose nails, then a cross-belt magnet on the discharge conveyor to catch metal that survives. Remove plastic wrap and stickers, and strip partial pallets with banding. Sort hardwood and softwood when chip grade matters.
| Feed issue | Solution |
|---|---|
| Nails and staples | Magnetic separator plus cross-belt magnet |
| Plastic wrap | Strip before feeding |
| Banding | Remove by hand |
| Mixed density | Batch by species when grade matters |
Machine Setup
Fit a magnetic head pulley and a cross-belt magnet rated for the discharge width. Set the screen at 2 to 3 inches for boiler fuel and 1 inch for animal bedding. Run the tub at 40 to 60 percent speed so the hammers keep up with dense pallet feed. Monitor the mill amps and slow the tub when the load climbs.
Feed Control
Feed pallets in a steady stream rather than dumping full batches, which surge-loads the mill. Use the loader to break up stacked pallets before they reach the tub. Watch the tub level: a starved tub wastes production and an overloaded tub plugs the screen. A consistent feed rate gives the highest tons per hour.
Daily Operating Routine
Spend 20 minutes each morning checking hammers, screens and magnet strength. Grease bearings and verify the emergency stop. Clear the cross-belt magnet and log hours. Pallet grinding wears hammers faster than clean wood, so keep spare sets on site and rotate tools on schedule.
Product Value
Clean pallet chips sell as boiler fuel, animal bedding and mulch. Bedding buyers want dust-free fines-free material; screen fines out of the sale pile. Boiler fuel tolerates mixed species but penalizes metal and fines. Review the tub grinder product page for pallet-rated options before purchase.
Frequently Asked Questions
Can a tub grinder handle pallets with nails?
Yes, with a magnetic separator, cross-belt magnet and regular magnet checks.
What screen should I use for pallet grinding?
Use a 2 to 3 inch screen for boiler fuel and a 1 inch screen for animal bedding.
What is pallet grinder throughput?
A mid-size tub grinder processes 15 to 30 tons per hour on pallets.
How often do hammers wear on pallets?
Nails and mixed density wear hammers faster than clean wood; check daily and rotate on schedule.
Quick Reference Setup Card
Keep this card near the control panel so operators can confirm the tub grinder setup for pallets before every shift.
| Setup item | Recommended setting |
|---|---|
| Screen hole size | 2 to 3 inches |
| Tub rotation | 60 to 80 percent |
| Hammer tip speed | 4,500 to 5,500 fpm |
| Mill box clearance | Match material size |
- Check hammer wear and screen condition at the start of each day.
- Confirm the discharge conveyor is aligned before the first load.
- Compare machine options in the tub grinder vs horizontal grinder guide and review the product range before buying.
Conclusion
A tub grinder for pallets earns best when metal removal and feed control are treated as production steps. Run the magnets, feed steadily and protect the hammers. For a pallet-rated machine sized to your volume, contact the WeiDong sales team for a setup recommendation.