· · 3 min read
Horizontal Grinder for Demolition Wood Setup Guide
A horizontal grinder for demolition wood setup guide helps C&D recyclers process pallets, framing and formwork into boiler fuel and mulch. Demolition wood carries nails, screws, wire and mixed contaminants, so metal defense and sorting decide whether the job profits or destroys the machine. WeiDong Machinery supplies horizontal grinders configured for C&D duty, and this guide covers metal defense, contaminant sorting and the daily routine.
Key Takeaways
- Run a magnetic separator plus cross-belt magnet for C&D feed.
- Sort painted, treated and plywood fractions by market.
- Use a 2 to 3 inch screen for boiler fuel.
- Expect 15 to 25 tons per hour on mixed demolition wood.
- Document hammer hours; C&D feed wears tools 30 to 50 percent faster.
Contaminant and Metal Defense
Demolition wood demands a two-stage metal defense. Stage one: a magnetic separator before the mill pulls loose nails and screws. Stage two: a cross-belt magnet on the discharge catches metal that survives. Sort loads for painted wood, treated wood, plywood and clean framing before feeding; each fraction has a different market.
| Contaminant | Handling |
|---|---|
| Nails and screws | Magnetic separator plus cross-belt magnet |
| Wire and rebar | Manual removal before feeding |
| Painted wood | Separate lot, fuel market |
| Treated wood | Separate lot, permitted fuel only |
| Concrete and drywall | Reject before grinding |
Machine Setup
Use a 2 to 3 inch screen for boiler fuel; fine screens clog on demolition mix. Fit a cross-belt magnet sized to the discharge width and check it daily. Set the chain speed at 30 to 50 percent so the mill keeps up with dense, mixed feed. Keep spare hammers on site; nails and grit wear tools fast.
Feed Control
Load demolition wood flat on the chain so it pulls squarely under the mill. Strip banding and remove heavy metal by hand. Monitor the mill amps and slow the chain when load spikes. A steady deck with good sorting outproduces a fast deck with contaminated feed.
Daily Operating Routine
Spend 20 minutes each morning checking hammers, magnets, screens, feed chain and drive belts. Grease bearings and verify the emergency stop. Clear the magnet catcher and log hours. On C&D feed, hammers typically last 300 to 500 hours versus 500 to 800 hours on clean wood.
Product Quality
Boiler fuel from demolition wood sells when metal and fines stay low. Mulch buyers avoid painted and treated wood, so keep those lots separate. Keep records of metal removal and treated wood segregation for audit. Review the horizontal grinder product page for C&D-rated options before purchase.
Frequently Asked Questions
Can a horizontal grinder handle nails in demolition wood?
Yes, with a magnetic separator, cross-belt magnet and daily magnet checks.
What screen should I use for demolition wood?
Use a 2 to 3 inch screen for boiler fuel; fine screens clog on demolition mix.
What is C&D grinder throughput?
A mid-size horizontal grinder processes 15 to 25 tons per hour on mixed demolition wood.
Why do hammers wear fast on C&D feed?
Nails, grit and mixed contaminants wear hammers 30 to 50 percent faster than clean wood.
Quick Reference Setup Card
Keep this card near the control panel so operators can confirm the horizontal grinder setup for demolition wood before every shift.
| Setup item | Recommended setting |
|---|---|
| Screen hole size | 2 to 3 inches |
| Rotor speed | 900 to 1,200 rpm |
| Feed chain speed | 30 to 60 percent |
| Magnet check | Daily |
- Check hammer and screen wear at the start of each day.
- Confirm the discharge belt and magnet are aligned before the first load.
- Compare machine options in the tub grinder vs horizontal grinder guide and review the product range before buying.
Conclusion
A horizontal grinder for demolition wood pays when metal defense and sorting are production steps. Run the magnets, separate the fractions and protect the hammers. For a C&D-rated machine sized to your volume, contact the WeiDong sales team for a setup recommendation.