· · 6 min read

Horizontal Grinder Specifications: kW, T/h, Output

Horizontal grinder specifications boil down to 4 numbers: engine power (150 to 800 kW), throughput (5 to 50 T/h), feed opening (0.8 to 1.5 m wide), and output size (25 to 150 mm screens). Brochure maximums assume ideal feed and the coarsest screen, so real-world specified-chip output usually lands 20 to 30 percent lower. This guide decodes each horizontal grinder specification, shows how the numbers relate, and teaches you to read any spec sheet like a factory engineer.

Key Takeaways

  • Power (150–800 kW) sets the ceiling; throughput (5–50 T/h) depends on screens, feed, and moisture as well.
  • Budget 15 to 20 kW per T/h of 25 to 50 mm specified chips as a sizing rule.
  • Feed opening width (0.8–1.5 m) limits the maximum log diameter and pallet throughput.
  • Screen size moves output 30 to 60 percent: coarse 100 mm grinds far faster than 25 mm fuel spec.
  • Always ask for throughput at your screen size and moisture — WeiDong Machinery reports all three together.

What Do Power Ratings Mean?

Engine kilowatts (and the HP equivalent at 1 kW = 1.34 HP) measure input power, not grinding work — drivetrain losses of 8 to 12 percent mean a 400 kW engine delivers roughly 355 to 368 kW at the rotor. Three ratings appear on spec sheets and they are not interchangeable:

  • Standby/max power — the 1-hour peak (e.g., 450 kW); useful for surge loads but not continuous grinding.
  • Prime/continuous power — the all-day rating (e.g., 400 kW); size your throughput math on this line.
  • Rotor kW — power after drivetrain losses; the honest figure for kW-per-ton calculations.

Tier ratings matter commercially: Tier 4 Final engines add 8 to 12 percent to price over Tier 3 export builds but hold resale in regulated markets and cut particulates 90 percent. Electric motors sidestep tiers entirely — a 350 kW electric drive matches a 400 kW diesel at the rotor while cutting energy cost 30 to 40 percent where 380 V supply exists. Compare power options across the horizontal grinder range using continuous ratings only.

How Is Throughput Measured?

Throughput in tons per hour is the most quoted and most misunderstood figure. Legitimate spec sheets state 3 conditions beside the T/h number — screen opening, material, and moisture — because each swings results enormously:

Condition changeEffect on throughputExample
Screen 100 mm → 50 mmDown 30 – 40%25 T/h → 15 – 17 T/h
Screen 50 mm → 25 mmDown further 20 – 30%16 T/h → 11 – 13 T/h
Clean pallets → mixed storm debrisDown 40 – 60%20 T/h → 8 – 12 T/h
Moisture 20% → 50% (green)Down 15 – 25%20 T/h → 15 – 17 T/h
Worn hammers (over 400 h)Down 10 – 20%20 T/h → 16 – 18 T/h

The sizing rule professionals use: 15 to 20 kW of continuous engine power per T/h of 25 to 50 mm specified chips. A buyer needing 20 T/h of biomass fuel should therefore shortlist 350 to 400 kW machines and verify with a sample grind — WeiDong Machinery tests customer material and reports fines percentage before quoting. Our sizing guide turns this rule into a 7-step selection with headroom math.

What Do Feed Opening and Output Specs Tell You?

Feed opening (width × height, e.g., 1.0 × 1.8 m) caps what enters the mill: whole-tree stems up to 600 to 900 mm diameter pass a 1.2 m opening, while pallet batches flow best at 1.0 m and above. Undersized openings force pre-cutting that adds $3 to $6 per ton in loader and saw time — a hidden cost buyers discover too late.

Output specs come as screen openings (25 to 150 mm) plus fines limits for contract work. Two machines with identical 50 mm screens can still differ: rotor speed (400–600 rpm), hammer count (24–48), and anvil gap shift the fines fraction from 3 percent to over 12 percent. Ask for a gradation curve — the percentage retained on 50, 25, and 10 mm sieves — rather than accepting "50 mm chip" at face value. Stock 2 screen sizes per machine ($3,000–$5,000 each) so one unit can serve mulch Mondays and fuel-spec Fridays.

How Do You Read a Spec Sheet in 5 Minutes?

Work this checklist top to bottom on any brand's sheet:

  1. Find continuous kW — ignore standby peaks; divide by your target T/h and check the 15–20 kW-per-ton rule.
  2. Read T/h conditions — screen size, material, moisture must be printed; unconditioned numbers deserve a 30 percent haircut.
  3. Check rotor data — diameter, width, hammer count, and 400–600 rpm speed range reveal whether the mill suits dirty or clean feed.
  4. Verify opening and discharge — feed width against your largest material; stacking conveyor length (30–50 ft) against your pile plan.
  5. Scan weights and transport — 18 to 35-ton operating weights decide permits; tracked units need lowboy trailers in 2 to 3 pieces.

Then cross-check price per rated ton: a $420,000 machine rated 20 T/h costs $21,000 per T/h of capacity versus $26,000 for a $520,000 unit rated the same — the gap usually hides in screens, wear packages, or engine tier. Photograph the dataplate and send it to the manufacturer: engineers can confirm continuous versus standby ratings from the serial prefix in minutes. Our 2026 price guide normalizes all 4 tiers, and genuine wear parts keep rated output honest across 1,500-hour years.

Frequently Asked Questions

What do horizontal grinder specifications mean?

Power (150–800 kW) is the energy ceiling, throughput (5–50 T/h) is output under stated screen/material/moisture conditions, feed opening (0.8–1.5 m) limits input size, and screen size (25–150 mm) sets chip size. Read all four together — no single number describes a machine.

How is throughput measured?

At a stated screen opening, feed material, and moisture content — e.g., 20 T/h through 50 mm screens on pallets at 25 percent moisture. Changing to 25 mm screens or green 50-percent-moisture wood cuts 20 to 40 percent off the headline figure.

How much power per ton per hour do I need?

15 to 20 kW of continuous engine power per T/h of 25 to 50 mm chips: 10 T/h needs about 175 kW, 20 T/h needs 350–400 kW, and 40 T/h needs 650–800 kW. Coarse mulch grinds need roughly 30 percent less power per ton.

Where can I get verified specification sheets?

Every model on the horizontal grinder page lists continuous kW, conditioned T/h, openings, and screen options — or send your material spec to our contact team for an engineer-matched sheet within 1 business day.

Spec the Machine, Not the Brochure

Conditioned numbers beat headline numbers every time. Demand continuous kW, T/h with screen-material-moisture stated, and a gradation curve — then validate with a sample grind before signing. WeiDong Machinery publishes all three for every model, and our engineers will benchmark any competitor's sheet line by line through contact.

Keep reading