· · 3 min read
Horizontal Grinder for Logs and Roundwood Setup Guide
A horizontal grinder for logs and roundwood setup guide helps operations convert logs and tree-length material into biomass chips and hog fuel. Horizontal grinders excel on roundwood because the chain infeed meters logs into the mill at a steady, controlled rate. WeiDong Machinery supplies horizontal grinders rated for log duty, and this guide covers chain infeed, log sizing, hammer setup and the daily routine.
Key Takeaways
- Cut logs to 12 to 20 feet and remove bark when chip grade matters.
- Use a medium hammer pattern for roundwood; heavy for large logs.
- Set the chain infeed to 40 to 60 percent speed for steady grinding.
- A 2 to 3 inch screen suits boiler fuel and hog fuel.
- A horizontal grinder processes 20 to 40 tons per hour on clean logs.
Log Preparation
Cut logs to 12 to 20 feet so the chain can pull them under the mill. Remove loose bark when the buyer wants clean chips; bark raises fines and ash. Wash sandy logs to protect hammers. Green logs grind easiest; seasoned logs raise fuel burn by 10 to 20 percent but produce drier output.
| Log condition | Machine impact |
|---|---|
| Bark on | Lower chip grade, higher fines |
| Sand and grit | Fast hammer wear |
| Oversize length | Chain jams and wear |
| Seasoned dry | Higher fuel burn, drier chips |
Hammer and Screen Setup
Select a medium hammer pattern for typical roundwood and a heavy pattern for large logs. Check hammer pins and balance before the first feed. Use a 2 to 3 inch screen for boiler fuel and hog fuel; a 1 inch screen makes premium mulch but cuts throughput. Set the chain speed at 40 to 60 percent so the mill keeps up.
Feed Control
Lay logs parallel to the chain so they pull squarely into the mill. Keep the infeed deck loaded but not overloaded; a starved deck wastes production and a jammed deck stops the line. Monitor the mill amps and adjust the chain speed before the load spikes.
Daily Operating Routine
Spend 20 minutes each morning checking hammers, screens, feed chain and drive belts. Grease bearings and verify the emergency stop. Rotate hammers on schedule and log hours. On clean logs, hammers typically last 500 to 800 hours; keep spare sets on site.
Product Value
Clean log chips sell as biomass fuel, mulch and animal bedding. Boiler contracts want chips under 50 mm with fines below 10 percent. Bedding buyers want dust-free fines-free material. Review the horizontal grinder product page for log-rated options before purchase.
Frequently Asked Questions
Can a horizontal grinder process full logs?
Yes, with logs cut to 12 to 20 feet and a medium or heavy hammer pattern.
What screen should I use for log grinding?
Use a 2 to 3 inch screen for boiler fuel and hog fuel; 1 inch for premium mulch.
What is horizontal grinder log throughput?
A mid-size unit processes 20 to 40 tons per hour on clean logs.
How long do hammers last on logs?
500 to 800 hours on clean logs with proper feed control.
Quick Reference Setup Card
Keep this card near the control panel so operators can confirm the horizontal grinder setup for logs and roundwood before every shift.
| Setup item | Recommended setting |
|---|---|
| Screen hole size | 2 to 3 inches |
| Rotor speed | 900 to 1,200 rpm |
| Feed chain speed | 30 to 60 percent |
| Magnet check | Daily |
- Check hammer and screen wear at the start of each day.
- Confirm the discharge belt and magnet are aligned before the first load.
- Compare machine options in the tub grinder vs horizontal grinder guide and review the product range before buying.
Conclusion
A horizontal grinder for logs and roundwood delivers high tonnage when logs are sized, hammer patterns are matched and the chain meters the feed. Keep the deck steady, protect the hammers and check daily. For a log-rated machine, contact the WeiDong sales team for a setup recommendation.