· · 7 min read
Wood Chipper Specifications: kW, T/h, Output
Wood chipper specifications describe 4 things: engine power in kW or HP, throughput in tons per hour, feed opening in inches or millimeters, and output chip size in millimeters. A typical mid-range sheet reads 168 kW, 10 to 15 T/h, 12-inch (300 mm) feed opening and 15 to 45 mm screened output. This guide decodes each wood chipper specifications line, shows the unit conversions buyers need, and teaches a 5-step method to read any spec sheet without getting misled by peak-only figures.
Key Takeaways
- Power is rated in kW or HP (1 HP equals 0.746 kW); commercial chippers span 55 kW to 500+ kW.
- Throughput in T/h is always a range: expect the lower figure in hardwood and the upper in softwood or pallet wood.
- Feed opening in inches or mm sets the largest branch the machine accepts — size it 2 inches above your typical maximum.
- Output size is set by screens, usually 15, 30 or 45 mm, with fines below 5 percent on sharp knives.
- Always compare sustained ratings at 8-hour shift output, not 15-minute peak claims.
What Do Wood Chipper Specifications Tell You?
A spec sheet answers 4 buying questions at a glance: can it swallow your largest material, can it hit your hourly target, what chip quality comes out, and what it costs to run. The 6 lines that matter most are engine power, throughput, feed opening, rotor type and speed, output screen sizes, and weight plus dimensions for transport. Everything else — paint color, tire brand, toolbox size — is noise at selection stage.
Keep dual units handy since US and export sheets differ:
| Quantity | US customary | Metric | Conversion |
|---|---|---|---|
| Engine power | 100 to 670 HP | 74 to 500 kW | 1 HP = 0.746 kW |
| Throughput | 2 to 66 tons/h | 2 to 60 T/h | 1 US ton = 0.907 T |
| Feed opening | 6 to 20+ in | 150 to 500+ mm | 1 in = 25.4 mm |
| Chip size | 0.5 to 2 in | 15 to 50 mm | screen opening |
| Machine weight | 4,400 to 44,000 lb | 2 to 20 t | 1 t = 2,205 lb |
When two sheets disagree on format, convert everything to kW, metric tons per hour and millimeters before comparing — 9 out of 10 "better specs" surprises vanish after conversion. Browse comparable sheets on our wood chipper lineup to practice.
How Is Engine Power Rated in kW and HP?
Manufacturers quote gross flywheel power under ISO 3046 or SAE J1995 — for example 168 kW (225 HP) on a 12-inch drum. Three details separate honest sheets from marketing sheets:
- Gross versus net — cooling fan and alternator consume 5 to 8 percent; a 168 kW gross engine delivers about 155 to 160 kW net at the rotor.
- Continuous versus peak — continuous (prime) rating is what an 8-hour shift sustains; 30-minute peak figures run 10 percent higher and mean nothing for daily output.
- Derating — naturally aspirated diesels lose about 1 percent of power per 100 meters above 1,000 meters altitude; turbocharged units hold rated power to 2,500 meters.
Rule of thumb: budget 10 to 15 kW per ton-hour of hardwood throughput. Modern turbo diesels burn 210 to 240 grams per kWh at full load, which works out to 25 to 45 liters per 8-hour shift on a 168 kW mid-range unit. A 10 T/h hardwood target needs roughly 120 to 150 kW net, while softwood or dry pallets need only 8 to 10 kW per ton-hour. Undersized power shows up as stalling on 300 mm logs and 20 percent higher fuel per ton — size up one engine step if 6 out of 10 loads are dense hardwood.
How Is Throughput Measured in T/h?
Rated throughput assumes ideal conditions: straight softwood, skilled operator, continuous grapple feed and sharp knives. Real shifts deliver 60 to 80 percent of the brochure maximum, so treat the quoted range honestly — a "10 to 15 T/h" machine gives 6 to 9 T/h in mixed hardwood with manual loading and the full 15 T/h only in dry pine with a grapple. Moisture matters too: green wood at 50 percent moisture weighs nearly twice as much per cubic meter as air-dried stock, inflating tons-per-hour while halving energy value per ton.
Four variables move measured throughput by 20 percent or more each:
- Species density — oak and acacia cut throughput 25 to 35 percent versus poplar or pine.
- Feed method — grapple loading beats manual feeding by 40 to 60 percent on the same rotor.
- Knife condition — dull edges cost 15 to 25 percent output plus oversize rejects.
- Screen size — 15 mm fuel screens pass 20 to 30 percent fewer tons per hour than 45 mm coarse screens.
Ask suppliers for shift logs, not brochure peaks: 3 consecutive 8-hour weighbridge tickets tell the truth. WeiDong Machinery provides reference-site data with every quotation — request it through our sales team and compare against any competitor's ticket-backed figures.
What Do Feed Opening and Output Size Mean?
Feed opening — the throat dimensions in inches or millimeters, such as 12 by 16 in (300 by 400 mm) — is a hard physical limit: anything larger simply does not enter. Size it at least 2 inches above your largest typical branch, because forked limbs bridge across openings 30 percent smaller than their spread. Rotor design behind the throat matters equally: drum rotors at 500 to 700 RPM pull aggressively and suit high volume, while disc rotors at 800 to 1,000 RPM cut more precisely for uniform pulp chips.
Output size is set by interchangeable screens with 15, 30 or 45 mm openings, and each end market specifies its own:
- Pellet and board mills: 20 to 30 mm with fines below 5 percent.
- Biomass boilers: 30 to 45 mm screened, oversize under 3 percent.
- Landscaping mulch: 30 to 50 mm coarse, color and shape matter more than tolerance.
Screen changes take 20 to 40 minutes with 2 workers, so yards serving 2 markets keep 2 screen sets minimum. For dirty mixed feed that would blind chipper screens in hours, our tub grinders and horizontal grinders use hammermill grates instead — compare both routes before committing.
How Do You Read a Spec Sheet?
Apply this 5-step check to every quotation in 10 minutes:
- Convert all figures to kW, metric T/h and mm, then verify power per ton-hour sits at 10 to 15 kW for hardwood.
- Confirm throughput is a sustained 8-hour rating with species and moisture stated — reject peak-only sheets.
- Check feed opening against your largest material plus the 2-inch bridging margin.
- Match screen options to your buyer's chip specification in millimeters, not adjectives like "fine" or "coarse."
- Verify transport weight and dimensions against your trailer limit (commonly 3.5, 12 or 20 tons) and container inner width of 2.35 meters.
Red flags that disqualify a sheet immediately: power quoted only in HP with no standard named, throughput as a single number with no range, no screen sizes listed, or weight missing. A supplier unwilling to provide 3 weighbridge-backed shift references is telling you the answer — WeiDong Machinery attaches reference data and a 12-month or 2,000-hour warranty statement to every formal quote.
Frequently Asked Questions
What do wood chipper specifications mean in practice?
They state what the machine accepts (feed opening in inches or mm), what it produces (tons per hour and chip size in mm) and what it consumes (kW or HP plus fuel per ton). Read sustained 8-hour ratings, not peak claims.
How is throughput measured on a wood chipper?
Throughput is measured in tons per hour over full shifts using weighbridge tickets, split by species and moisture. Expect 60 to 80 percent of brochure maximum in real mixed-wood operation with manual loading.
How many kW does a wood chipper need per ton?
Budget 10 to 15 kW per ton-hour for hardwood and 8 to 10 kW for softwood or pallets. A 10 T/h hardwood duty therefore needs roughly 120 to 150 kW net at the rotor.
What chip size do pellet plants require?
Most pellet and board mills specify 20 to 30 mm chips with fines below 5 percent. Confirm the exact screen in millimeters on your purchase order — adjectives like "fine" cause rejected loads.
What does rotor speed tell you on a spec sheet?
Drum rotors run 500 to 700 RPM for aggressive high-volume cutting, while disc rotors run 800 to 1,000 RPM for precise uniform chips. Higher speed alone means nothing without matched torque — check kW per ton-hour first.
Next Step
Send WeiDong Machinery your target tons per hour, species mix and required chip size for a spec-matched recommendation with ticket-backed references. Start at the wood chipper lineup or message our sales team for an ex-works quote within one business day.