· · 3 min read
Tub Grinder for Demolition Wood Setup Guide
A tub grinder for demolition wood setup guide helps C&D recyclers process construction and demolition wood into boiler fuel and mulch. Demolition wood is the most dangerous tub feed: nails, screws, concrete and treated lumber all arrive mixed. The setup has to defend the machine with magnets and screening at every stage. WeiDong Machinery builds demolition-rated tub grinders, and this guide covers metal removal, hazard sorting, screens and the daily routine.
Key Takeaways
- Run a triple metal defense: inspection, magnetic separator, cross-belt magnet.
- Reject or sort treated, painted and engineered wood by contract.
- Use a 3 inch screen for demolition fuel; fines go to disposal.
- Plan 25 to 40 percent downtime for sorting and metal removal.
- Track metal removal and hammer hours for facility compliance.
Hazard Sorting
Demolition wood needs sorting before grinding. Remove nails, screws, steel plates and rebar; concrete and masonry chips destroy hammers. Separate treated lumber, painted wood and engineered panels when the fuel contract rejects them. Sort by grade into saleable fuel, mulch and reject piles.
| Hazard | Action |
|---|---|
| Nails and screws | Magnetic separator plus cross-belt magnet |
| Steel plates and rebar | Manual removal at sorting station |
| Concrete and masonry | Reject before grinding |
| Treated and painted wood | Sort per contract |
Machine Setup
Fit a magnetic head pulley and a cross-belt magnet rated for the discharge width. Use a 3 inch screen: demolition fuel tolerates coarse chips, and a fine screen plugs with mixed feed. Run the tub at 40 to 60 percent speed and monitor the mill amps. Keep a full spare hammer set and spare screen on site.
Metal Defense Workflow
Stage the operation with three checkpoints: inspection at the dump point, magnetic separator on the feed line and cross-belt magnet on the discharge. Assign an operator to the sorting station when volume justifies it. Log metal removal per shift; facilities with documented metal control win better contracts.
Daily Operating Routine
Spend 25 minutes each morning checking hammers, screens, magnets and drive belts. Grease bearings, verify the emergency stop and clear the magnet catcher. At shift end, run clean wood through the unit, inspect the rotor and log hours.
Compliance and Product
Demolition fuel buyers test for metal, chlorine and treated wood content. Screen the final pile and reject contaminated batches. Track inputs and outputs by truck count for compliance audits. Review the tub grinder product page for demolition-rated options before purchase.
Frequently Asked Questions
Can a tub grinder handle demolition wood?
Yes, with a triple metal defense: inspection, magnetic separator and cross-belt magnet.
What screen should I use for demolition wood?
Use a 3 inch screen. Demolition fuel tolerates coarse chips and fine screens plug.
Is treated wood safe to grind?
Only if the fuel contract allows it; otherwise sort treated, painted and engineered wood into reject piles.
How much downtime should I plan?
Plan 25 to 40 percent downtime for sorting and metal removal on demolition feed.
Quick Reference Setup Card
Keep this card near the control panel so operators can confirm the tub grinder setup for demolition wood before every shift.
| Setup item | Recommended setting |
|---|---|
| Screen hole size | 2 to 3 inches |
| Tub rotation | 60 to 80 percent |
| Hammer tip speed | 4,500 to 5,500 fpm |
| Mill box clearance | Match material size |
- Check hammer wear and screen condition at the start of each day.
- Confirm the discharge conveyor is aligned before the first load.
- Compare machine options in the tub grinder vs horizontal grinder guide and review the product range before buying.
Conclusion
A tub grinder for demolition wood runs safe when metal removal and hazard sorting are production steps, not afterthoughts. Run the magnets, use a tolerant screen and track the rejects. For a demolition-rated machine, contact the WeiDong sales team for a setup recommendation.