· · 5 min read
Tub Grinder Specifications: kW, T/h, Output
Tub grinder specifications look intimidating, but 6 numbers tell you 90 percent of what matters: engine power in HP and kW, rated throughput in tons per hour, tub diameter, rotor dimensions, screen size range, and transport weight. A mid-range machine typically lists 400 to 600 HP (300 to 450 kW), 35 to 55 T/h, a 10 ft (3.0 m) tub, and 25 to 150 mm screen options. This guide decodes every line of a tub grinder spec sheet so you can compare models honestly.
Key Takeaways
- Power (300–1,000+ HP / 220–750+ kW) sets the ceiling; throughput (20–80+ T/h) is what you actually buy.
- Rated T/h assumes dry, clean wood — derate 15 to 25 percent for wet or dirty material.
- Tub diameter (8–12 ft / 2.4–3.7 m) limits the maximum single-piece size you can drop in.
- Screen openings (25–150 mm) define every saleable product from fine mulch to coarse hog fuel.
- Always compare weight, rotor size, and hammer count alongside headline power — they reveal real build class.
What Do Tub Grinder Specifications Mean?
Each spec line answers one buying question. Here is the decoder:
- Engine power (HP/kW) — the maximum energy available; 1 HP equals 0.746 kW. More power sustains throughput in hard, dirty, or frozen wood.
- Rated throughput (T/h) — tons per hour under reference test conditions; your real number depends on material, screens, and operator skill.
- Tub diameter and height — the 8 to 12 ft opening dictates grapple loading ease and maximum log length without pre-cutting.
- Rotor diameter and width — bigger rotors (36 to 48 in / 900 to 1,200 mm diameter) carry more inertia and stall less on stumps.
- Hammer count and type — 20 to 40 hammers; fixed-tooth rotors bite aggressively while free-swinging hammers forgive tramp metal.
- Screen sizes (mm/in) — interchangeable grates from 25 mm (1 in) to 150 mm (6 in) that set final particle size.
- Discharge height and reach — 12 to 18 ft stacking height determines pile size before a loader must push up.
- Transport dimensions and weight — 25,000 to 50,000 kg total; check bridge and permit limits in your operating states.
Full worked examples for each class are published on our tub grinder product page.
Power Ratings: HP, kW, and What They Mean
| Class | Rated power | kW equivalent | Fuel burn at full load | Rotor speed |
|---|---|---|---|---|
| Compact | 300 – 400 HP | 220 – 300 kW | 40 – 55 L/h | 1,000 – 1,400 RPM |
| Mid-range | 400 – 600 HP | 300 – 450 kW | 55 – 75 L/h | 1,200 – 1,600 RPM |
| Industrial | 600 – 1,000+ HP | 450 – 750+ kW | 75 – 120 L/h | 1,400 – 1,800 RPM |
Three power traps to avoid:
- Peak vs continuous ratings — some brochures quote 30-second peak power 10 percent above continuous; size jobs on continuous output only.
- Derating with altitude and heat — turbo-diesel output falls 3 to 4 percent per 1,000 ft (300 m) of altitude and 2 to 3 percent above 40°C (104°F); high-site buyers should upsize one class.
- Electric equivalents — a 350 kW electric motor roughly matches a 500 HP diesel in sustained grinding because electrics hold torque without refueling stops; compare our electric-drive options if your yard has 3-phase supply.
How Is Throughput Measured in T/h?
Manufacturers measure rated throughput by grinding oven-dry pine or clean pallets through a mid-size screen for 60 minutes with an expert operator — ideal conditions almost nobody replicates. Adjust quoted T/h to your reality with 4 derating factors:
- Moisture: green wood at 45 to 55 percent moisture cuts throughput 15 to 25 percent versus 20 percent-moisture test wood.
- Contamination: 3 to 5 percent soil and rock content cuts 10 to 20 percent and doubles hammer wear.
- Screen size: fine 25 mm mulch screens pass 30 to 40 percent fewer tons per hour than coarse 100 mm hog-fuel screens on the same machine.
- Feed discipline: a skilled grapple operator adds 10 to 20 percent over an average one by keeping the tub evenly loaded.
Practical rule: multiply brochure T/h by 0.7 to 0.8 for mixed land-clearing work. A machine rated 50 T/h reliably delivers 35 to 40 T/h on real jobsites — size your fleet and your quotes on the derated number, then confirm expectations with our engineering team before purchase.
Reading a Spec Sheet: Worked Example
Here is how to read a typical mid-range tub grinder spec block line by line:
| Spec line | Example value | What to check |
|---|---|---|
| Engine | 540 HP / 403 kW diesel | Continuous rating, emissions tier, service access |
| Throughput | Up to 50 T/h | Test material and screen size behind the headline |
| Tub | 10 ft / 3.0 m diameter | Fits your grapple bucket and max log length |
| Rotor | 42 in / 1,067 mm, 28 hammers | Inertia class and hammer replacement cost |
| Screens | 25 – 150 mm, 4 segments | Spare set price and same-day swap time |
| Discharge | 15 ft / 4.6 m stacking height | Pile volume before loader push-up needed |
| Weight | 34,000 kg operating | Permits, trailers, and ground pressure |
Red flags on any sheet: missing test conditions for T/h, no screen size quoted, transport weight omitted, or hammer count hidden — all 4 suggest the headline numbers flatter the machine. WeiDong Machinery publishes full test conditions with every model; compare openly against any competitor sheet.
Frequently Asked Questions
What do tub grinder specifications mean?
They describe power (HP/kW), throughput (T/h), tub and rotor dimensions, screen size range, and transport weight. Together these 6 groups determine what material the machine handles, how fast, and into which saleable products.
How is throughput measured?
Manufacturers grind dry, clean wood through a mid-size screen for 60 minutes under ideal conditions. Multiply the rated T/h by 0.7 to 0.8 for real-world mixed material, and more like 0.6 for wet or contaminated storm debris.
What screen size should I choose?
25 to 50 mm for landscape mulch and compost cover, 50 to 75 mm for general biomass, and 100 to 150 mm for coarse hog fuel. Most contractors stock 3 screen sizes and swap them in under 2 hours per changeover.
How many horsepower does a tub grinder need?
300 to 400 HP for municipal and small mulch work at 20 to 35 T/h, 400 to 600 HP for most contracting at 35 to 55 T/h, and 600 to 1,000+ HP for biomass and heavy clearing at 55 to 80+ T/h.