· · 3 min read
Tub Grinder for Bark and Slabs Setup Guide
A tub grinder for bark and slabs setup guide helps sawmills convert bark, edgings and slabs into mulch, boiler fuel and bedding. Bark is fibrous and stringy; slabs are dense and heavy, so the two fractions need different hammer and screen strategies. WeiDong Machinery supplies tub grinders rated for mill residue, and this guide covers hammer configuration, screens, feed control and the daily routine.
Key Takeaways
- Grind bark and slabs as separate fractions for clean product.
- Use a heavy hammer pattern for slabs and anti-wrap rings for bark.
- A 2 to 3 inch screen suits mulch and boiler fuel.
- Separate sand and grit from bark before grinding.
- A mill residue grinder processes 15 to 35 tons per hour.
Fraction Separation
Run bark and slabs as separate streams so each gets the right settings. Bark is fibrous and wraps mills; slabs are dense and hammer-heavy. Debark logs before sawing so bark stays clean. Knock sand and grit off bark stockpiles; gritty bark wears hammers 30 to 50 percent faster.
| Fraction | Grinding profile |
|---|---|
| Clean bark | Fibrous, anti-wrap needed |
| Sand-laden bark | Wash or reject, fast wear |
| Slabs and edgings | Dense, heavy hammers |
| Trim ends | Cut to feed length |
Machine Setup
Use a heavy hammer pattern for slabs and standard pattern with anti-wrap rings for bark. Set the screen at 2 to 3 inches for mulch and boiler fuel; a 1 inch screen makes premium mulch but cuts throughput. Run the tub at 40 to 60 percent speed on slabs and 30 to 50 percent on bark.
Feed Control
Feed slabs in steady streams so the mill stays at full bite. Bark should be fed in loose batches to avoid wrap. Monitor the mill amps and slow the loader when load spikes. Alternate heavy and light feed to hold a stable tub level. A steady feed gives the highest tons per hour with the least tool wear.
Daily Operating Routine
Spend 20 minutes each morning checking hammers, anti-wrap rings, screens and drive belts. Grease bearings, verify the emergency stop and clear the magnet. Rotate hammers on schedule; slab work wears hammers faster than bark.
Product Value
Clean bark mulch sells at premium prices; sand and grit contaminate the grade. Slab chips work as boiler fuel and animal bedding. Boiler buyers want chips under 50 mm with low fines. Review the tub grinder product page for mill residue options before purchase.
Frequently Asked Questions
Can I grind bark and slabs in one pass?
Yes, but running them as separate fractions with different hammer settings gives cleaner product and less wear.
What screen should I use for bark and slabs?
Use a 2 to 3 inch screen for mulch and boiler fuel; 1 inch for premium mulch.
How do I stop bark wrapping the mill?
Fit anti-wrap rings and feed bark in loose batches.
What is mill residue grinder throughput?
A mid-size tub grinder processes 15 to 35 tons per hour on bark and slabs.
Quick Reference Setup Card
Keep this card near the control panel so operators can confirm the tub grinder setup for bark and slabs before every shift.
| Setup item | Recommended setting |
|---|---|
| Screen hole size | 2 to 3 inches |
| Tub rotation | 60 to 80 percent |
| Hammer tip speed | 4,500 to 5,500 fpm |
| Mill box clearance | Match material size |
- Check hammer wear and screen condition at the start of each day.
- Confirm the discharge conveyor is aligned before the first load.
- Compare machine options in the tub grinder vs horizontal grinder guide and review the product range before buying.
Conclusion
A tub grinder for bark and slabs earns the most when the two fractions are handled separately with matched tooling. Keep bark clean, use heavy hammers for slabs and feed steadily. For a mill residue machine, contact the WeiDong sales team for a setup recommendation.