· · 4 min read

Straw Shredder for Logs and Roundwood: Setup Guide

A straw shredder for logs and roundwood is one of the most asked-about configurations in the wood processing industry because operators already own the machine for agri-residue and want a second revenue stream. With a deep throat, high-torque rotor and the right screen, the same machine can produce boiler chips and pulp-grade material at 10 to 25 tons per hour. This setup guide covers the realistic throughput band, screen selection, debarking trade-offs and the daily plan, based on WeiDong Machinery installations.

Key Takeaways

  • A straw shredder processes clean roundwood at 10 to 25 tons per hour with 350 to 600 hp.
  • Use a 30 to 60 mm screen for boiler chips; pre-chipping large logs is recommended above 400 mm diameter.
  • Bark adds 5 to 10 percent ash; debark only when the buyer pays a premium for clean fiber.
  • Fuel consumption runs 25 to 45 liters per hour depending on power and moisture.
  • WeiDong supplies a log-rated rotor, full-width apron and automatic feed control.

Is a Straw Shredder the Right Machine for Roundwood?

Roundwood is consistent, dense and free of metal, which makes it a forgiving feed for a straw shredder. The main constraint is the throat opening: a standard straw shredder accepts logs up to 300 to 400 mm without preparation, while bigger diameter material must be split or sawn. In energy wood yards, the machine runs near rated output all day because logs feed predictably and hammer wear is low compared with stumps or pallets.

Capacity planning follows chip demand. A 20 t/h machine running 6 hours per day produces 120 tons, roughly 3,000 cubic meters a month, which is a typical small heating plant order. The investment case improves when the same line also processes bark, slabs and offcuts on off days.

Throughput Benchmarks: 10 to 25 Tons Per Hour

Power classLog diameterTypical throughputChip moisture
350 hpup to 250 mm10 to 14 t/hfresh 45%
500 hpup to 350 mm14 to 19 t/hfresh 45%
900 hpup to 450 mm19 to 25 t/hfresh 45%

Moisture changes output: green wood at 45 to 55 percent moisture is easier to chip than partly dried wood with the same density. Seasonal drying swings throughput by 10 to 15 percent, which has to be planned in the weekly production schedule.

Screen and Rotor Setup

Start with a 40 mm screen for boiler chips. For pellet plant feedstock, a 25 to 30 mm screen is standard and throughput drops 10 to 15 percent. Keep a 60 mm screen for mulch production so the mill never sits idle when the chip market is soft.

  • Rotor speed: 850 to 1,000 rpm for roundwood.
  • Screen clearance: 5 to 10 mm to avoid stringy edge chips.
  • Feed table: full-width apron with hydraulic pusher.
  • Magnet: optional for clean roundwood, mandatory if recycling scrap.

Contamination and Wear Management

Roundwood feed has few metal risks, but a stray nail from previous milling can break a hammer. Run a light magnet on the feed table as insurance. The real wear comes from bark and dirt trapped under the bark: keep the rotor area clean and rotate hammers every 150 to 250 hours on clean roundwood. Check the screen for edge wear monthly and replace when holes deform.

Operating Routine for a Roundwood Line

Start the shift with a 10-minute walk down. Check the apron chain, hydraulic oil level, screen condition and the hammer bolts on the first 20 cm of the rotor. Record amps at the start and end. Logs with large butt swell should be fed butt-first to prevent jams at the throat, and the feed speed should drop to 70 percent when the log is more than 350 mm in diameter.

Chip Production Plan and ROI

At $50 per delivered ton for boiler chips, a 15 t/h machine generates $4,500 in market value during a 6-hour run. Operating costs of roughly $1,300 for fuel, $400 for wear parts and $450 for labor leave a margin over $2,000 per day in most energy markets. For a machine configured to your log mix, contact the WeiDong sales team and review the wood chip production application page and the straw shredder product range.

Frequently Asked Questions

What size logs can a straw shredder handle?

A standard straw shredder accepts logs up to 300 to 400 mm diameter; larger logs need splitting or sawing first.

What is the throughput on roundwood?

Clean roundwood produces 10 to 25 tons per hour depending on power, diameter and moisture.

Should I debark before shredding?

Only when the buyer pays a clean-grade premium; otherwise bark adds 5 to 10 percent ash with no revenue gain.

What screen do I need for boiler chips?

Use a 40 mm screen for boiler chips and 25 to 30 mm for pellet feedstock.

Final Recommendation

A straw shredder for logs and roundwood is a low-wear, high-schedule line that earns steady gross margin when the screen matches the buyer. Buy the log-rated package from WeiDong, keep a spare screen on site and let the automatic feed control protect the mill. For pricing and delivery, use the contact page.

Keep reading