· · 7 min read

Wood Chipper Guide 2026: Types, Sizes, Uses

A wood chipper is a machine that cuts branches, logs and wood waste into uniform chips for mulch, biomass fuel or compost. Capacities range from 2 tons per hour on compact 6-inch models to more than 60 tons per hour on industrial drum units, with diesel power from 74 kW to over 400 kW. This 2026 guide explains how a wood chipper works, compares drum, disc and screw types, and matches each size class to the right job so you can shortlist with confidence.

Key Takeaways

  • A wood chipper converts branches, logs and pallet wood into uniform chips at 2 to 60 T/h depending on size class.
  • Drum chippers suit high-volume biomass work, disc chippers suit clean uniform chips, and screw chippers suit small farms.
  • Match feed opening to your largest material: 6-inch for landscaping, 12 to 15 inch for municipal work, 20-inch-plus for industrial plants.
  • Diesel power from 74 kW to 400+ kW covers most jobs; electric drives cut fuel cost where grid supply is available.
  • WeiDong Machinery builds factory-direct chippers that typically cost 20 to 40 percent less than dealer-listed equivalents.

What Is a Wood Chipper?

A wood chipper is a size-reduction machine built around a cutting rotor — either a drum or a disc fitted with 2 to 8 replaceable knives — that slices incoming wood against a fixed anvil. A feed system of powered rollers or a grapple loader pulls branches and logs into the cutting chamber at a controlled rate, while interchangeable screens set the final chip size between 10 mm and 50 mm. Most commercial units process material with up to 30 percent moisture without clogging, and produce 50 to 120 cubic meters of chips per 8-hour shift depending on throughput. Rotor diameters run 400 to 800 mm, with tip speeds of 40 to 60 meters per second for clean shearing cuts.

Unlike grinders that smash material with hammers, a wood chipper cuts cleanly, which keeps chip geometry consistent and fines below 5 percent. That consistency is why paper mills, pellet plants and biomass boilers specify chipped wood over shredded wood in roughly 7 out of 10 fuel contracts. Browse the full wood chipper lineup to compare feed openings, power ratings and throughput side by side.

How Does a Wood Chipper Work?

The working cycle has 4 stages from infeed to discharge:

  1. Infeed — branches or logs up to the rated diameter enter through powered feed rollers running at 10 to 40 meters per minute.
  2. Cutting — the drum or disc rotor spinning at 500 to 1,000 RPM slices wood against the anvil into chips of set length.
  3. Sizing — chips pass through screens with 15 mm to 50 mm openings; oversize pieces recirculate for a second cut.
  4. Discharge — a blower or belt conveyor throws chips 5 to 15 meters into a truck, pile or trailer.

Knife sharpness controls everything: dull knives raise fuel use by 15 to 25 percent and double the share of oversize chips. Operators typically rotate or replace knives every 40 to 80 working hours, a 30-minute job on modern quick-change rotors. For mixed waste streams that include nails or dirt, many yards pair a chipper with one of our tub grinders that tolerate contaminants better.

Which Wood Chipper Types and Sizes Fit Your Job?

Three rotor designs cover nearly every application, and size is set by feed opening:

TypeFeed openingThroughputPowerBest for
Disc chipper6 to 12 in / 150 to 300 mm2 to 15 T/h55 to 200 kWClean uniform chips for landscaping and pulp
Drum chipper12 to 20 in / 300 to 500 mm10 to 40 T/h150 to 400 kWMunicipal debris, pallets, biomass fuel
Industrial drum20 in / 500 mm and up30 to 60+ T/h300 to 500+ kWBiomass plants, storm cleanup, sawmills

Selection rules that buyers use most:

  • Size the feed opening at least 2 inches above your largest typical branch to avoid bridging and jams.
  • Match throughput to your weekly volume: under 50 tons favors compact units, while over 300 tons justifies an industrial drum.
  • Choose tracked undercarriage for soft or sloped ground; it adds about 10 to 15 percent to the price but prevents most stuck-machine downtime.

If your material includes demolition timber or root balls, compare our horizontal grinders before deciding — grinders handle contaminated feed that would damage chipper knives within days.

What Is a Wood Chipper Used For?

Five end markets absorb most chipped wood:

  • Mulch and landscaping — decorative chips sell for $15 to $45 per cubic yard at retail garden centers.
  • Biomass fuel — power plants burn 10,000 to 200,000 tons per year of screened chips at 15 to 19 MJ/kg.
  • Pellet and board feedstock — uniform chips dry 20 to 30 percent faster than random shred, cutting dryer fuel cost.
  • Compost and animal bedding — coarse 30 to 50 mm chips balance carbon-to-nitrogen ratios in windrow composting.
  • Site clearing residue — contractors reduce 100 truckloads of branches to roughly 12 loads of chips, saving up to 80 percent on haulage.

Each market specifies chip size, so confirm the buyer's screen requirement — usually 20, 30 or 45 mm — before ordering screens with your machine. Send your material photos and target tonnage to our sales team for a matched recommendation within one business day.

How Much Does a Wood Chipper Cost in 2026?

Entry 6-inch chippers start near $8,000, mid-range 12 to 15 inch machines sit between $25,000 and $70,000, and industrial 20-inch-plus units cost $100,000 to $180,000 or more. Power unit, feed system and mobility explain most of the spread: diesel engines add $5,000 to $40,000 over the base chassis, auto-feed adds $8,000 to $25,000, and tracked running gear adds 10 to 15 percent. Factory-direct buying from WeiDong Machinery removes importer margin and typically lands 20 to 40 percent below dealer quotes for equal capacity.

Budget 3 to 6 percent of the purchase price per year for knives, anvils and screens. At 1,500 operating hours per year, a $50,000 mid-range chipper costs roughly $20,000 to $25,000 annually to run including diesel at $12 to $20 per ton produced.

Frequently Asked Questions

What is a wood chipper best used for?

A wood chipper is best used for converting clean branches, logs and pallet wood into uniform chips for mulch, biomass fuel or compost. It handles 2 to 60 T/h depending on size, with fines below 5 percent when knives are sharp.

How does a wood chipper differ from a wood shredder?

A wood chipper cuts wood cleanly with knives for uniform chips, while a shredder smashes material with hammers and tolerates nails and dirt. Choose a chipper for fuel-grade output and a shredder or grinder for contaminated mixed waste.

What size wood chipper do I need for 10 tons per hour?

A 12-inch drum chipper rated at 10 to 15 T/h with 150 to 200 kW of power covers that target. Size the feed opening at least 2 inches above your largest branch to prevent bridging.

How long do wood chipper knives last?

Knives last 40 to 80 working hours between sharpenings in clean wood, and 15 to 30 hours in dirty or sandy material. Rotating a full set takes about 30 minutes on quick-change rotors.

Can a wood chipper handle wet or green wood?

Yes, up to about 30 percent moisture without clogging, though green wood nearly doubles weight per cubic meter and cuts energy value per ton. Knives dull 20 to 30 percent faster in wet bark, so shorten the sharpening interval from 80 toward 40 hours in rainy-season clearing work.

Get a Factory-Direct Quote

Tell WeiDong Machinery your material type, largest diameter and target tonnage, and receive a model match with an ex-works price within one business day. Start from the wood chipper lineup or message our sales team directly — standard models ship in 15 to 30 days with export packing included.

Keep reading