· · 3 min read
Tub Grinder for Logs and Roundwood Setup Guide
A tub grinder for logs and roundwood setup guide helps operations convert logs and tree-length material into biomass chips and hog fuel. Roundwood is a clean, high-value feedstock, but tub grinders need the right hammer configuration and feed control to process it efficiently. WeiDong Machinery supplies tub grinders rated for log duty, and this guide covers log sizing, feed control, hammer setup and the daily routine.
Key Takeaways
- Cut logs to 12 to 20 feet and remove bark when chip grade matters.
- Use a medium hammer pattern for roundwood; heavy for large logs.
- Run the tub at 40 to 60 percent speed for steady grinding.
- A 2 to 3 inch screen suits boiler fuel and hog fuel.
- A tub grinder processes 20 to 40 tons per hour on clean logs.
Log Preparation
Cut logs to 12 to 20 feet so the tub can pull them under the mill. Remove loose bark when the buyer wants clean chips; bark raises fines and ash. Wash sandy logs to protect hammers. Green logs grind easiest; seasoned logs raise fuel burn by 10 to 20 percent but produce drier output.
| Log condition | Machine impact |
|---|---|
| Bark on | Lower chip grade, higher fines |
| Sand and grit | Fast hammer wear |
| Oversize length | Tub jams and wear |
| Seasoned dry | Higher fuel burn, drier chips |
Hammer and Screen Setup
Select a medium hammer pattern for typical roundwood and a heavy pattern for large logs. Check hammer pins and balance before the first feed. Use a 2 to 3 inch screen for boiler fuel and hog fuel; a 1 inch screen makes premium mulch but cuts throughput. Set the tub speed at 40 to 60 percent so the mill keeps up.
Feed Control
Feed logs in a steady stream with the loader, keeping the tub level stable. A starved tub wastes production; an overloaded tub plugs the screen. Cross logs so the mill draws them evenly. Monitor the mill amps and adjust the tub feed before the load spikes.
Daily Operating Routine
Spend 20 minutes each morning checking hammers, screens and drive belts. Grease bearings and verify the emergency stop. Rotate hammers on schedule and log hours. On clean logs, hammers typically last 500 to 800 hours; keep spare sets on site.
Product Value
Clean log chips sell as biomass fuel, mulch and animal bedding. Boiler contracts want chips under 50 mm with fines below 10 percent. Bedding buyers want dust-free fines-free material. Review the tub grinder product page for log-rated options before purchase.
Frequently Asked Questions
Can a tub grinder process full logs?
Yes, with logs cut to 12 to 20 feet and a medium or heavy hammer pattern.
What screen should I use for log grinding?
Use a 2 to 3 inch screen for boiler fuel and hog fuel; 1 inch for premium mulch.
What is tub grinder log throughput?
A mid-size unit processes 20 to 40 tons per hour on clean logs.
How long do hammers last on logs?
500 to 800 hours on clean logs with proper feed control.
Quick Reference Setup Card
Keep this card near the control panel so operators can confirm the tub grinder setup for logs and roundwood before every shift.
| Setup item | Recommended setting |
|---|---|
| Screen hole size | 2 to 3 inches |
| Tub rotation | 60 to 80 percent |
| Hammer tip speed | 4,500 to 5,500 fpm |
| Mill box clearance | Match material size |
- Check hammer wear and screen condition at the start of each day.
- Confirm the discharge conveyor is aligned before the first load.
- Compare machine options in the tub grinder vs horizontal grinder guide and review the product range before buying.
Conclusion
A tub grinder for logs and roundwood delivers high tonnage when logs are sized, hammer patterns are matched and the feed stays steady. Keep the tub level, protect the hammers and check daily. For a log-rated machine, contact the WeiDong sales team for a setup recommendation.